Skip to content

Trucking and fleet

Your trucks run back empty because loads are planned one at a time. One model matches loads, drivers and hours for the whole week.

  • Free 30-minute call
  • No commitment
  • You own the code
Typical decisions
vehicle routing optimisation, bid and RFP analysis
What you gain
Loads, drivers, hours and prices in one weekly plan, return loads included
First step
A free 30-minute call

Typical problems in trucking and fleet.

You assign each load as it comes in, to whichever driver is free. The truck delivers in Milan on Thursday and drives home empty on Friday.

Empty kilometres

A truck delivers in Milan and drives home empty. You pay for the fuel, the driver and the wear, and earn nothing.

Loads mismatched

Loads go to whoever is free right now. The driver who could take the return load is two hours away.

Driving hours run out

After a late change, a driver drives longer than he may per day. You only find out from the tachograph, the device that records driving time.

Bids priced blind

You price a tender with the average cost per kilometre of your whole fleet. You win the route and learn later that you lose money on every load.

In short: A fleet dispatch optimisation assigns loads to trucks and drivers for the whole week with a mathematical model. It plans loads, driving and rest times and return trips together, so fewer trucks drive back empty.

Empty kilometres are lost margin

Thursday afternoon, and a truck unloads in Milan with no load for the trip home. Another driver picks up freight forty kilometres away and heads north half full. Each decision made sense when it was made. Together they send two trucks home with space nobody sold.

Every empty kilometre costs fuel, driver hours and wear, and earns nothing. Your plan decides three things. The first is your deadhead rate, the share of kilometres your trucks drive empty. The second is how many of their hours your drivers spend driving loads. The third is how much revenue each truck brings in. When loads are assigned one at a time, the plan never sees the empty return leg.

Deadhead reduction with a plan for the whole week

Today, you plan loads, then drivers, then driving hours and then prices. Each step locks in the mistakes of the last. Our model plans all four together for the whole week. It sees the return load before the outbound trip is booked.

You see each plan’s deadhead rate, driver utilisation and revenue per truck before the trucks leave. Every driver stays within driving and rest limits, because the limits are in the model. Sometimes a customer asks several carriers for their prices. This is called a tender. When you make your offer, you know what each route in it costs you.

Fleet dispatch optimisation in one model

We optimise load planning, load-to-driver matching, deadhead and driving times together. Driving times are the limits on driving and rest that every driver works within. Matching is an assignment problem: which driver takes which load, at the lowest total cost? Trucking route optimisation uses the same methods as our [vehicle routing](/use-cases/routing/vehicle-routing/). For tenders, lane profitability shows what each regular route between two points costs, including the empty return. The model works for full truckload (TL), where one customer fills the whole truck. It also works for less-than-truckload (LTL), where several customers share one truck.

How many hours can a truck really move in a day?

Dispatch tools count kilometres. Your drivers’ day counts hours. Each driver has a daily driving limit, a break after a stretch at the wheel and a minimum rest before the next day. Heavy trucks also have hours when they can’t run at all.

Put those together, and a driver has fewer hours for loads than the shift suggests. Take a driver who finishes late after a long unload. The rest he needs pushes his start well past the hour trucks may roll again, so the morning is lost. Move the unload one hour earlier and he starts an hour sooner. A model sees that trade when it assigns the load, while you usually find it on the tachograph.

How a project runs.

Each of the three phases ends with something you can check before we go any further.

  1. Understand

    We start with your operation. What do you plan, where does it go wrong, and what would a better week look like? Then we tell you straight whether optimisation can help, and sometimes the answer is no.

    • A written assessment
    • A clear go or no-go
  2. Model

    We write your decisions, goals and rules into a mathematical model, which is just a precise description of how your operation works. Then we run it on your own data. You see side by side what each plan costs and what it delivers, and pick the one that fits your priorities.

    • A documented model
    • Results on your own data
  3. Implement

    We test with your data and go through the results with your team. Once they trust it, we connect the model to your systems, so it runs every day without anyone stepping in by hand.

    • Source code and documentation
    • Training for your team

Common questions.

Something else? Ask us directly.

Plan the return load before you book the outbound trip. That takes a view of the whole week, rather than one load at a time. Assign drivers and loads for all your routes together. Then you find return loads you miss when you plan each load on its own. Count every week how many kilometres your trucks drive empty, so you know whether the number is going down.

Sometimes. Price the empty return into the load and compare it with what else that truck could earn. If this route often has a return load later in the week, it can pay to take the load and let the truck wait there for it. A model answers this load by load, with the hours and costs of your own fleet.

More than you’d expect. Each driver may only drive a set number of hours a day. He has to take a break after a few hours at the wheel and needs a minimum rest before the next start. If one truck is unloaded late, the driver may start hours later the next morning. A model checks every assignment against those limits, so the plan never books a driver who can’t take the load.

It depends on the problem, so we agree the timeline with you up front. Every project starts with a diagnostic, a short look at how you plan today. It shows which data, how much time and what budget a model for daily use needs. Only then do you decide.

No. We connect to your ERP, your warehouse management system or your planning spreadsheet. We build the model only for the planning that gives you trouble today. Your systems keep running as before.

Almost nobody’s data is clean. The diagnostic shows what the model needs and what’s missing. Then we build the model to cope with messy data.

Off-the-shelf tools are built for many companies at once, so they don’t know your special rules. We build a model that follows exactly your rules. Then we hand it over, and your team owns it.

Tell us what you’re planning.

In a free 30-minute call with a specialist, you find out whether optimisation can help.

  • Free, no commitment
  • You talk to a specialist directly
  • A clear go or no-go